A pre-ride checklist is a must every time you are about to take your motorcycle for a ride, but how many of us really do it every time? Here are the top ten things a motorcyclist should do regularly, especially if you're one of the many who don't make a pre-ride check every time you ride. All you need are some hand tools and basic mechanical ability. The more you know machine, the better will be your riding experience.
Check the fluids. Start with the engine oil. If it's been a while since you've ridden, start the engine and let it run for about 5 minutes (fast idle is best - around 1500 RPM). This allows the oil pump to return any oil to the tank that may have seeped past the check ball in the pump, and it allows the oil to warm up slightly, giving you a more accurate check. Oil expands with heat, and your oil level will rise as the bike warms up. Check the oil in the correct position, with the bike to on the side stand or upright as recommended by the factory. Next, check the transmission oil level, following the correct procedure for your model. If your motorcycle has a wet clutch, check the primary oil level. Use Syntehtic motor oil. I prefer AMSOIL.
Check the battery. New motorcycles use a sealed battery, but older bikes still need your attention. Remove the battery for a thorough inspection, checking for corrosion at the terminals and cracks or leakage around the case. Make sure the vent hose isn't cut, pinched or plugged. Verify that it's routed correctly, away from chains, belts and exhaust pipes. The end should hang down about 1" to 2" below the frame of the bike. Finally, check the fluid in each cell. This is easy to do since most batteries have a translucent case, but you might need to shine a flashlight through the case to see the level clearly. If needed, add distilled water, being careful not to overfill. Never add tap water - it contains too many minerals and will damage the plates. Reinstall the battery.
Check the rear drive belt or chain. As chains and sprockets wear, they develop tight and loose spots. Find the tight spot in your chain before you check it. If you adjust it in a loose spot it may bind when it rolls around to the tight spot. To check for excessive wear, push up with one hand on the lower section of the chain, removing all slack. Then, with your other hand, grab the chain halfway up the backside of the sprocket by the side plates. Try to pull the chain away from the sprocket teeth. If it pulls away by more than half the diameter of the roller, you should replace the chain, the rear drive sprocket and the transmission counter sprocket as a complete set. Installing a new chain on worn sprockets will cause the chain to wear prematurely. Lube your chain, but ride the bike a few miles first. This allows the chain to warm up and expand, permitting the lubricant to reach critical parts inside the rollers. For belts, make sure the tension is correct for your model. Then inspect the belt for rocks and tooth separation. Have a friend roll the bike slowly as you watch for foreign objects embedded in the belt. If your bike has high miles, or if you live in a dusty, sandy climate, be sure to check the rear sprocket.
Inspect the tires. Make sure the air pressure is correct for the tire type and riding application - solo or two up. Check the tread for nails or screws. Again, enlist the aid of a buddy to roll the bike as you inspect the tire tread. The tire's tread should have at least 3/32" depth at the thinnest part. Most tires have safety bars incorporated into the tread pattern. As the tire wears down, the safety bar will cause the tread pattern to appear smooth all the way across in swath about two inches wide. Watch for weather checking and cracks in the tread or sidewall area.
Inspect the air filter. Remove the cover and filter element. For foam or K&N type filters remove the element from the screen, wash it out with hot, soapy water and blot it dry. Then apply the correct filter oil (don't over do it - too much oil is as bad as none). If you have a paper filter and it's dirty or contaminated with oil or water, replace it. You can not clean paper filters.
Check your throttle and clutch cables adjustment. Excess slack can cause riding problems or contribute to an accident. While you're at it, lube the cables. Dry cables increase effort and are the number one cause of cable failure. The best way is pressure lube cables is with a good quality cable lubricant and cable lubing tool - the type that clamps over and seals the end of the cable housing while allowing the cable itself to pass through. A can of lubricant is connected to the tool with a capillary tube. When actuated, the entire cable housing can be filled with lubricant.
Check the operation of headlights, taillights, brake lights, turn signals, etc. It might save you more than peace of mind.
Inspect brake lines and pads along with brake fluid levels. Make sure the lines show no evidence of cracking or leaks at fittings or junctions. Brake pads should never have less than 1/8" of material on either pad. Then look at the disc. If it shows heavy grooving, scoring or cracks, replace it along with a fresh set of pads. When checking brake fluid levels, be sure to clean around the reservoir cap before removing it to prevent contamination. Use the correct fluid for your application DOT-4 or DOT-5 fluid. Respect and take care of your brakes and they will take care of you. Know your machine, become your machine. Zen has alot to do with motorcycling.
Tighten those fasteners and bolts. These are the most neglected area of maintenance. Depending on what your ride is and how you ride, you may never have problems with fasteners coming loose. On the other hand, if you have a V-twin that vibrates so much your girlfriend love your bike more than you, then you will need to keep checking this bolts and re-torque using the lock-tite. Pay close attention to front and rear motor mounts, exhaust system and shock absorber mounts, belt/chain guards and, mirrors. My mirrors alway vibrate loose. Thank God for lock-tite, it puts everything back nice and snug.
Check for loose spokes (unless you have mag wheels, of course). Put the bike on a lift and rotate the wheel, using a spoke wrench. Also inspect the rim for excess run out. Use a pointer (an old coat hanger works well for this) anchored to something solid on the frame, swing arm or front end. Tighten only the loosest spokes - no more than a quarter turn per adjustment. Over tightening spokes will cause unwanted offset in the wheel, not to mention creating a bind on other spokes. Wheel spokes tend to stretch over a period of time. When new, they find their "sweet spot", as the spoke ends and nipples seat into the hub and rim, allowing spokes to loosen. After the break-in and a good spoke tightening/truing process, they continue to stretch, so the spoke tightening and truing should be done yearly or every 10,000 miles.
Contributing author to the Victory Custom shop -- Cycle Solutions http://www.CycleSolutions.net
and the Victory Kingpin Cruiser Enthusiast site http://www.KingpinCruisers.net
About the Author
Contributing author to the Victory Custom shop -- Cycle Solutions http://www.CycleSolutions.net
and the Victory Kingpin Cruiser Enthusiast site http://www.KingpinCruisers.net
|
